Double-walled pipes with corrugated outer layer made of PE with the necessary additives to resist ultraviolet radiation from sunlight.
Uses
Suitable for installation buried directly in the ground without additional protection. Indicated for the installation of electrical networks, telecommunication lines, water pipes, gas pipes, etc.
Suitable for photovoltaic installations both in the underground section and in the exits to the outside.
Characteristics
Colours
Black
Conductor
Copper
Dimensions
UNE-EN 61386-24
Packing
Rolls
Standard
UNE-EN 61386-24
Compressive strength
450 N
UV resistance
The resistance to ultraviolet radiation of these tubes has been checked by means of an additional test to the AENOR brand certification. This test is the one prescribed in the UNE 21123 standard for 0.6/1KV cables and is carried out in accordance with the UNE 211605:2013 standard.
Impact resistance
15 J for 40 and 50, 20 J for 63, 75 and 90, 28 J for 110 and 125 and 40 J for 160, 200
Technical data
| Diámetro nominal (mm) | Diámetro exterior (mm) | Tolerancias (mm) | Diámetro interior mínimo (mm) |
|---|---|---|---|
| 40 | 40 | +0,8 | 30 |
| 50 | 50 | +1 | 37 |
| 63 | 63 | +1,2 | 47 |
| 75 | 75 | +1,4 | 56 |
| 90 | 90 | +1,7 | 67 |
| 110 | 110 | +2 | 82 |
| 125 | 125 | +2,3 | 94 |
| 160 | 160 | +2,9 | 120 |
| 200 | 200 | +3,6 | 150 |
| Diámetro nominal (mm) | 40 |
|---|---|
| Diámetro exterior (mm) | 40 |
| Tolerancias (mm) | +0,8 |
| Diámetro interior mínimo (mm) | 30 |
| Diámetro nominal (mm) | 50 |
|---|---|
| Diámetro exterior (mm) | 50 |
| Tolerancias (mm) | +1 |
| Diámetro interior mínimo (mm) | 37 |
| Diámetro nominal (mm) | 63 |
|---|---|
| Diámetro exterior (mm) | 63 |
| Tolerancias (mm) | +1,2 |
| Diámetro interior mínimo (mm) | 47 |
| Diámetro nominal (mm) | 75 |
|---|---|
| Diámetro exterior (mm) | 75 |
| Tolerancias (mm) | +1,4 |
| Diámetro interior mínimo (mm) | 56 |
| Diámetro nominal (mm) | 90 |
|---|---|
| Diámetro exterior (mm) | 90 |
| Tolerancias (mm) | +1,7 |
| Diámetro interior mínimo (mm) | 67 |
| Diámetro nominal (mm) | 110 |
|---|---|
| Diámetro exterior (mm) | 110 |
| Tolerancias (mm) | +2 |
| Diámetro interior mínimo (mm) | 82 |
| Diámetro nominal (mm) | 125 |
|---|---|
| Diámetro exterior (mm) | 125 |
| Tolerancias (mm) | +2,3 |
| Diámetro interior mínimo (mm) | 94 |
| Diámetro nominal (mm) | 160 |
|---|---|
| Diámetro exterior (mm) | 160 |
| Tolerancias (mm) | +2,9 |
| Diámetro interior mínimo (mm) | 120 |
| Diámetro nominal (mm) | 200 |
|---|---|
| Diámetro exterior (mm) | 200 |
| Tolerancias (mm) | +3,6 |
| Diámetro interior mínimo (mm) | 150 |
